Kia Cadenza: Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Kia Cadenza YG 2016-2024 Service Manual / Restraint / Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Removal

Set the front tires straight-ahead before removing the steering wheel.

If the steering wheel and the front tires are not set straight ahead together, it affects the number of circulation of steering wheel and the cable inside the clock spring is possible to be damaged.

Disconnect the battery negative cable.

After disconnecting the battery negative cable, wait for at least thirty seconds.

3.	Remove the driver airbag module mounting bolts.

4.	Remove the wiring fixing clip (C) and disconnect the horn connector (A).

Release the connector locking pin, then disconnect the driver airbag module connector (B).

The removed airbag module should be stored in a clean, dry place with the pad cover facing up.

6.	Remove the steering wheel and steering wheel column shroud. (Refer to Steering System - "Steering Column and Shaft")

7.	Disconnect the clock spring and horn connector, then remove the clock spring.

Inspection

Driver Airbag (DAB)

If any improper parts are found during the following inspection, replace the airbag module with a new one.

Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.

1.	Check pad cover for dents, cracks or deformities.

2.	Check the airbag module for denting, cracking or deformation.

3.	Check hooks and connectors for damage, terminals for deformities, and harness for binds.

4.	Check airbag inflator case for dents, cracks or deformities.

5.	Install the airbag module to the steering wheel to check for fit or alignment with the wheel.

Clock Spring

1.	If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.

2.	Check connectors and protective tube for damage, and terminals for deformities.

Installation

Set the front tires straight-ahead before assembling the steering wheel.

If the steering wheel and the front tires are not set straight ahead together, it affects the number of revolutions of steering wheel and the cable inside the clock spring is possible to be damaged.

Disconnect the battery negative cable.

After disconnecting the battery negative cable, wait for at least thirty seconds.

Set the clock spring in center before assembling it to a steering wheel.

(1)	Turn the clock spring clockwise or counter clockwise until it is locked in center automatically with sound of click.

(2)	Check the orange indicater in the clock spring.

4.	Connect the clock spring harness connector and horn harness connector to the clock spring.

5.	Install the steering wheel column cover and the steering wheel. (Refer to the Steering System group- Steering Column and Shaft)

6.	Connect the Driver Airbag (DAB) module connector, and then install the Driver Airbag (DAB) module on the steering wheel.

Secure the Driver Airbag (DAB) with the new mounting bolts.

Tightening torque :

7.8 ~ 10.8 Nm (0.8 ~ 1.1 kgf.m, 5.8 ~ 8.0 lb.ft)

8.	Connect the battery negative cable.

After installing the airbag, confirm proper system operation.

–	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

–	Make sure horn works.

Driver Airbag (DAB) Module and Clock Spring Components and Components Location

Components 1. Driver Airbag (DAB)2. Steering Wheel3. Clock Spring ...

Passenger Airbag (PAB) Module Description and Operation

Description Passenger Airbag (PAB) module is located in the passenger crash pad. This PAB contains 2 firing squibs of airbag and 1 firing squib of active vent. Depending of crash speed or the t ...

Other information:

Kia Cadenza YG 2016-2024 Service Manual: Engine Control Module (ECM) Schematic Diagrams

ECM Terminal And Input/Output signal ECM Terminal Function Connector [E600-A] Pin No.DescriptionConnected to1-　2-　3-　4Immobilizer Lamp control outputImmobilizer Lamp [Without Button Engine Start System]5Power groundChassis Ground6Power groundChassis Ground7-　8-　92nd CAN [High]Mu ...

Kia Cadenza YG 2016-2024 Service Manual: Interior Trim Repair procedures

Replacement Door Scuff Trim Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. • Take care not to bend or scratch the trim and panels. 1. ...