Inspection 1. Ignition "OFF". 2. Disconnect the intake actuator connector. 3. Verify that the actuator operates to the recirculation position when connecting 12V to the terminal 3 and grounding terminal 7.
Components (1) [DIGITAL CLOCK TYPE] Connector Pin Function ConnectorPin NoFunctionConnectorPin NoFunctionA1ILL + (TAIL)A31PHOTO SENSOR (-) LEFT2SENSOR REF(+5V)32PHOTO SENSOR (-) RIGHT3HAZARD SIGNAL33HTD4ACC34REAR DEFOG S/W5MODE ACT''R (VENT)35K-LINE6MODE ACT''R (DEF)36-7MODE ACT''R F/B37-8INTAKE ACT''R (FRE)38-9INTAKE ACT''R (REC)39-10INTAKE ACT''R F/B40SENSOR GND11TEMP ACT''R DR (COOL)B1GND12TEMP ACT''R DR (WARM)2-13TEMP ACT''R DR F/B3DEF ACT''R (CLOSE)14TEMP ACT''R PS (COOL)4DEF ACT''R (OPEN)15TEMP ACT''R PS (WARM)5DEF ACT''R F/B16TEMP ACT''R PS F/B6HUMIDITY (PWM)17C_CAN HIGH7-18C_CAN LOW8IGN219DETENT OUT(+)9GND20ILL - (RHEO)10-21ION SIGNAL11BLOWER MOTOR (+)22CLEAN SIGNAL12FET (GATE)23IONIZER DIAGNOSIS13FET (DRAIN F/B)24MM_CAN HIGH14-25MM_CAN LOW15IGN126AMB SENSOR (+)16BATTERY27- 28EVAP SENSOR (+) 29ECV + 30ECV - (GND) Components (2) [ANALOG CLOCK TYPE] Connector Pin Function ConnectorPin NoFunctionConnectorPin NoFunctionA1ILL + (TAIL)A31PHOTO SENSOR (-) LEFT2SENSOR REF(+5V)32PHOTO SENSOR (-) RIGHT3HAZARD SIGNAL33HTD4-34REAR DEFOG S/W5MODE ACT''R (VENT)35K-LINE6MODE ACT''R (DEF)36-7MODE ACT''R F/B37PAB_IGN18INTAKE ACT''R (FRE)38PAB CUT OFF SIGNAL9INTAKE ACT''R (REC)39SBR SIGNAL10INTAKE ACT''R F/B40SENSOR GND11TEMP ACT''R DR (COOL)B1GND12TEMP ACT''R DR (WARM)2-13TEMP ACT''R DR F/B3DEF ACT''R (CLOSE)14TEMP ACT''R PS (COOL)4DEF ACT''R (OPEN)15TEMP ACT''R PS (WARM)5DEF ACT''R F/B16TEMP ACT''R PS F/B6HUMIDITY (PWM)17C_CAN HIGH7-18C_CAN LOW8IGN219DETENT OUT(+)9GND20ILL - (RHEO)10-21ION SIGNAL11BLOWER MOTOR (+)22CLEAN SIGNAL12FET (GATE)23IONIZER DIAGNOSIS13FET (DRAIN F/B)24MM_CAN HIGH14-25MM_CAN LOW15IGN126AMB SENSOR (+)16BATTERY27- 28EVAP SENSOR (+) 29ECV + 30ECV - (GND) Components (3) [UVO TYPE] Connector Pin Function ConnectorPin NoFunctionConnectorPin NoFunctionA1ILL + (TAIL)A31PHOTO SENSOR (-) LEFT2SENSOR REF(+5V)32PHOTO SENSOR (-) RIGHT3HAZARD SIGNAL33HTD4ACC34REAR DEFOG S/W5MODE ACT''R (VENT)35K-LINE6MODE ACT''R (DEF)36-7MODE ACT''R F/B37PAB_IGN18INTAKE ACT''R (FRE)38PAB CUT OFF SIGNAL9INTAKE ACT''R (REC)39SBR SIGNAL10INTAKE ACT''R F/B40SENSOR GND11TEMP ACT''R DR (COOL)B1GND12TEMP ACT''R DR (WARM)2-13TEMP ACT''R DR F/B3DEF ACT''R (CLOSE)14TEMP ACT''R PS (COOL)4DEF ACT''R (OPEN)15TEMP ACT''R PS (WARM)5DEF ACT''R F/B16TEMP ACT''R PS F/B6HUMIDITY (PWM)17C_CAN HIGH7-18C_CAN LOW8IGN219DETENT OUT(+)9GND20ILL - (RHEO)10-21-11BLOWER MOTOR (+)22-12FET (GATE)23-13FET (DRAIN F/B)24-14-25-15IGN126AMB SENSOR (+)16BATTERY27- 28EVAP SENSOR (+) 29ECV + 30ECV - (GND)
Description Back view camera will activate when the backup light is ON with the ignition switch ON and the shift lever in the R position. This system is a supplemental system that shows behind the vehicle through the ECM (Reverse Display Room Mirror) mirror or AVN head unit while backing-up.
Description 1. The ambient temperature sensor is located at the front of the condenser and detects ambient air temperature. It is a negative type thermistor resistance will increase with lower temperature, and decrease with higher temperatures.