Kia Cadenza: Seat Belt / Front Seat Belt Repair procedures

Kia Cadenza YG 2016-2025 Service Manual / Body (Interior and Exterior) / Seat Belt / Front Seat Belt Repair procedures

Replacement

Front Seat Belt Replacement

•	When installing the belt, make sure not to damaged the pretensioner.

Remove the following items first :

•	Front seat assembly (Refer to the BD group - "Front Seat")

•	Front and rear door scuff trim (Refer to the BD group - "Interior Trim")

2.	The seat belt anchor pretensioner (A) be removed after pushing the lock pin (B) as arrow direction.

3.	Remove the center pillar lower trim (A).

4.	After loosening the mounting bolts, then remove the center pillar upper trim (A) .

After loosening the mounting bolt, then remove the upper anchor (A).

Tightening torque :

39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

After disconnecting the pretensioner connector lock pin, remove the SIS connector (A), loosen the mounting bolt, then remove the pretensioner (B).

Tightening torque :

39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

7.	Installation is the reverse of removal.

Height Adjust Replacement

Remove the following items first :

•	Front seat assembly (Refer to the BD group - "Front Seat")

•	Front door scuff trim & Rear door scuff tirm (Refer to the BD group - "Interior Trim")

•	Front seat belt lower anchor

•	Center pillar lower trim (Refer to the BD group - "Interior Trim")

•	Center pillar upper trim (Refer to the BD group - "Interior Trim")

•	Front seat belt upper anchor

After loosening the bolts, then remove the height adjustor (A).

Tightening torque :

39.2 ~ 53.9 N.m (4.0 ~ 5.5kgf.m, 28.9 ~ 39.8 lb-ft)

Installation is the reverse of removal.

•	Replace ant damaged clips.

•	Make sure the height adjust properly.

Front Seat Belt Buckle Replacement

1.	Remove the front seat assembly. (Refer to the BD group - "Front Seat")

After loosening the mounting bolt, then remove the front seat belt buckle (A).

Tightening torque :

39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.	Disconnect the connector mounting clip (A).

4.	Installation is the reverse of removal.

Components and Components Location

Components 1. Front seat belt2. Height adjuster3. Rear seat belt (RH)4. Rear center seat belt5. Rear seat belt (LH)6. Rear center seat belt buckle ...

Rear Seat Belt Repair procedures

Replacement Rear Seat Belt Retractor Replacement • When installing the belt, make sure not to damaged the retractor. 1. Remove the following items first ...

Other information:

Kia Cadenza YG 2016-2025 Service Manual: Mode Control Actuator Repair procedures

Inspection 1. Ignition "OFF” 2. Disconnect the connector of mode control actuator. 3. Verify that the mode control actuator operates to the defrost mode when connecting 12V to the terminal 3and grounding terminal 7. 4. Verify that the mode control actuator operates to the vent mo ...

Kia Cadenza YG 2016-2025 Service Manual: Repair procedures

Removal 1. Remove the trunk trim in the trunk after removing the screws and clips. (Refer to Body - "Trunk") 2. Remove the camera holder (A) as shown arrow direction, and then remove the back view camera (B). Installation 1. Install the back view camera and camera holder. 2. Instal ...