Kia Cadenza: Brake System / Rear Disc Brake Repair procedures

Kia Cadenza YG 2016-2025 Service Manual / Brake System / Brake System / Rear Disc Brake Repair procedures

Removal

Remove the rear wheel & tire.

Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.	Release the parking brake.

3.	Disconnect the EPB actuator connector (A). [EPB Only]

4.	Remove the rear shock absorber (B). (Refer to Suspension System - "Rear shock absorber")

5.	Remove the rear upper arm (A).

Loosen the hose eyebolt (B) and caliper mounting bolts (C), then remove the rear caliper assembly (A).

Tightening torque:

Brake hose to caliper(B):

24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)

Caliper assembly to carrier(C):

63.7 ~ 73.5 N.m (6.5 ~ 7.5 kgf.m, 47.0 ~ 54.2 lb-ft)

[Without EPB]

[With EPB]

Remove the rear brake disc by loosening the screws (A).

Tightening torque :

4.9 ~ 5.9 N.m (0.5 ~ 0. 6 kgf.m, 3.6 ~ 4.3 lb-ft)

Replacement

Rear brake pads (Without EPB)

1.	Remove the rear wheel & tire.

2.	Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.

3.	Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper bracket (A).

4.	Use a SST (09581-11000) when installing the brake caliper assembly.

Place the caliper body (A) on the caliper carrier and tighten the guide rod bolts (B).

Tightening torque:

21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

Install the rear wheel & tire.

Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

Rear brake pads (With EPB)

1.	Remove the rear wheel & tire.

2.	Connect the GDS to the data link connector located underneath the dash panel.

3.	Ignition "ON" & Engine "OFF".

4.	Release the electric parking brake.

5.	Select vehicle name and EPB system.

6.	Select the “PAD change mode”.

7.	Select the "C2(Release)".

8.	Ignition "OFF".

9.	Disconnect the electric parking brake actuator connector (A).

10.	Loosen the guide rod bolts (B) and then remove caliper body.

11.	Replace pad retainers (C) and brake pads (B) in the caliper carrier (A).

12.	Use a SST (09580-0U000) when installing the brake caliper assembly.

13.

Place the caliper body (A) on the caliper carrier and tighten the guide rod bolts (B).

Tightening torque:

21.6 ~ 31.4 N.m (2.2 ~ 3.2 kgf.m, 15.9 ~ 23.1 lb-ft)

14.	Connect the electric parking brake actuator connector (A).

15.	Ignition "ON".

16.	Select the “PAD change mode”.

17.

Select the "C1(Apply)".

Check that the parking brake operates normally.

18.	IGN switch “OFF” and remove the GDS.

19.

Install the rear wheel & tire.

Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

Inspection

Rear Brake Disc Thickness Check

1.	Check the brake pads for wear and fade.

2.	Check the brake disc for damage and cracks.

Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.

Rear Brake disc thickness

Standard: 10 mm (0.39 in)

Service limit: 8.4 mm (0.33 in)

Deviation: less than 0.01 mm (0.00039 in)

4.	If wear exceeds the limit, replace the discs and pad assembly left and right of the vehicle.

Rear Brake Pad Check

Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.

Pad thickness

Standard value: 10 mm (0.393 in)

Service limit: 2.0 mm (0.0787 in)

2.	Check that grease is applied, to sliding contact points and the pad and backing metal for damage.

Rear Brake Disc Runout Check

Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc.

Brake disc runout

Limit: 0.05 mm (0.00197 in.) or less (new one)

2.	If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.

3.	If the runout exceeds the limit specification, install the brake disc after turning it 180° and then check the runout of the brake disc again.

4.	If the runout cannot be corrected by changing the position of the brake disc, replace the brake disc.

Installation

1.	Installation is the reverse of removal.

2.	Use a SST (09581-11000, 09580-0U000) when installing the brake caliper assembly. [Without EPB] [With EPB]

3.	After installation, bleed the brake system. (Refer to Brake system bleeding)

Rear Disc Brake Components and Components Location

Components (Without EPB) 1. Guide rod bolt2. Bleed screw3. Caliper carrier4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer Components (With EPB) 1. Guide rod bolt2. Bleed screw3. ...

Parking Brake System

...

Other information:

Kia Cadenza YG 2016-2025 Service Manual: Front Seat Belt Repair procedures

Replacement Front Seat Belt Replacement • When installing the belt, make sure not to damaged the pretensioner. 1. Remove the following items first : • Front seat assembly (Refer to the BD group - "Front Seat") • Front and rear do ...

Kia Cadenza YG 2016-2025 Owners Manual: Inside rearview mirror

Adjust the rearview mirror so that the center view through the rear window is seen. Make this adjustment before you start driving. Do not place objects in the rear seat or cargo area which would interfere with your vision through the rear window. WARNING - Mirror adjustment Do not adjus ...