Kia Cadenza: AVN System / Roof Antenna Repair procedures

Kia Cadenza YG 2016-2024 Service Manual / Body Electrical System / AVN System / Roof Antenna Repair procedures

Removal

1.	Remove the rear roof trim. (Refer to Body - "Roof Trim")

2.	Disconnect the connector (A) and cable (B) from the roof antenna.

3.	Remove the roof antenna after removing a nut (A).

Installation

1.	Installation the roof antenna.

2.	Connect the connector and cable.

Install the rear roof trim.

–	Make sure that the cables and connectors are plugged in properly.

–	Check the AVN system.

Inspection

Glass Antenna Test

1.	Wrap aluminum foil (A) around the tip of the tester probe (B) as shown.

2.	Touch one tester probe to the glass antenna terminal (A) and move the other tester probe along the antenna wires to check that continuity exists.

Glass Antenna Repair

To make an effective repair, the broken section must be no longer than one inch.

1.	Lightly rub the area around the broken section (A) with fine steel wool, and then clean it with alcohol.

2.	Carefully mask above and below the broken portion of the glass antenna wire (B) with cellophane tape (C).

Using a small brush, apply a heavy coat of silver conductive paint (A) extending about 1/8″on both sides of the break. Allow 30 minutes to dry.

Thoroughly mix the paint before use.

4.	Check for continuity in the repaired wire.

5.	Apply a second coat of paint in the same way. Let it dry three hours before removing the tape.

Glass Antenna Circuit Inspection

1.	Remove the right side rear quarter trim. Then disconnect the antenna feeder cable from the glass antenna amp.

Turn the radio ON.

Measure the voltage between terminal 2 of the harness side feeder cable (A) and body ground (B).

OK : approximately 12V (ACC+)

Check for FM wire resistance between terminals of No.1 and 3

1. FM antenna grid terminal

2. AM antenna grid terminal

3. Body ground.

Standard value : 80~120KΩ (Average : 100 kΩ)

Short : Approx. 0Ω

Open : ∞ Ω

Check for AM wire resistance between terminals of No.2 and 3.

Standard value : 120~170KΩ (Average : 145 kΩ)

Short : Approx. 0Ω

Open : ∞ Ω

5.	Check the grid lines for continuity.

6.	When a poor radio reception is not repaired through the above inspection methods, replace the amp. If the radio reception is still poor, check the radio cable for short and radio head unit for failure.

Antenna Cable

1.	Remove the antenna jack (A) from the audio unit and antenna.

2.	Check for continuity between the center poles of antenna cable.

3.	Check for continuity between the outer poles of antenna cable. There should be continuity.

4.	If there is no continuity, replace the antenna cable.

5.	Check for continuity between the center pole (A) of antenna cable and terminal of glass antenna (B). There should be continuity.

6.	If there is no continuity, replace the antenna amplifier.

7.	Check for continuity between the center pole (A) and outer pole (B) of antenna cable. There should be no continuity.

8.	If there is continuity, replace the antenna cable.

Speaker Repair procedures

Inspection 1. Troubleshooting for Speaker (1) Basic inspection of speaker Inspect the sound from speaker after verifying that the speaker mounting screws are removed and the wiring connector ...

Steering Wheel Remote Controller (SWRC) Components and Components Location

Components Location 1. Remote control switch (Audio) [LH]2. Remote control switch (Cruise) [RH]3. Bluetooth hands fress switch4. Trip switch5. Rear seat remote control switch ...

Other information:

Kia Cadenza YG 2016-2024 Service Manual: Canister Close Valve (CCV) Repair procedures

Inspection 1. Turn the ignition switch OFF. 2. Disconnect the CCV connector. 3. Measure resistance between the CCV terminal 1 and 2. 4. Check that the resistance is within the specification. Specification: Refer to "Specification" 5. Disconnect the vapor hose connected with ...

Kia Cadenza YG 2016-2024 Service Manual: Components and Components Location

Component Location Index Engine Room 1. Receiver Drier2. Condenser3. Service Port (High Pressure)4. Service Port (Low Pressure)5. APT6. Compressor7. Expension Valve Interior ...