Kia Cadenza: Automatic Transaxle Control System / SS-A Solenoid Valve(ON/OFF) Repair procedures

Kia Cadenza YG 2016-2024 Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / SS-A Solenoid Valve(ON/OFF) Repair procedures

Inspection

1.	Turn ignition switch OFF.

2.	Remove the battery and battery tray. (Refer to Engine Electrical System - "Battery")

3.	Disconnect the solenoid valve connector (A).

Measure the resistance between power terminal (10) and signal terminal (18).

Specification : 10.0 ~ 11.0 Ω

Removal

1.	Remove the under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")

Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.

Tightening torque:

33.3 ~ 43.1 N.m (3.4 ~ 4.4 kgf.m, 24.6 ~ 31.8 lb-ft)

The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)

3.	Remove the battery and battery tray. (Refer to Engine Electrical System - "Battery")

Remove the wiring bracket (A) and the air breather hose (B).

Tightening torque:

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

5.	Lift the vehicle after loosening valve body cover upper bolts.

Remove the valve body cover (A) by loosening bolts.

Tightening torque:

11.8 ~ 13.7 N.m (1.2 ~ 1.4 kgf.m, 8.7 ~ 10.1 lb-ft)

Remove the solenoid valve harness (A) and oil temperature sensor (B) after removing the bolts.

Tightening torque:

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Remove solenoid valve support bracket (A).

Tightening torque:

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

9.	Remove the SS-A solenoid valve (A).

Installation

1.	Install in the reverse order of removal.

•	The existing solenoid valve O-ring (A) must be replaced with new one. (Do not reuse it.)

•	The existing valve body cover gasket (A) must be replaced with new one. (Do not reuse it.)

•	Refill the automatic transaxle with fluid. (Refer to Hydraulic System - "Fluid")

•	Confirm that there is no fluid leakage on connections after repairing.

SS-A Solenoid Valve(ON/OFF) Schematic Diagrams

Circuit Diagram ...

SS-B Solenoid Valve(ON/OFF) Specifications

Specification ItemSpecificationControl typeON/OFFCurrent value (mA)5.0 Coil resistance(Ω)10 ~ 11 ...

Other information:

Kia Cadenza YG 2016-2024 Owners Manual: Tire sidewall labeling

This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall. 1. Manufacturer or brand name Manufacturer or ...

Kia Cadenza YG 2016-2024 Service Manual: Knock Sensor (KS) Repair procedures

Removal [Knock Sensor #1 (Bank 1)] 1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Disconnect the knock sensor connector (A). 3. Remove the intake manifold. (Refer to Engine Mechanical System - "Intake Manifold") 4. Remove the installation bolt ...